Study of Stress on Belt Drive System Integrated with Briquetting Plant- Juniper Publishers

Juniper Publishers- Journal of Robotics



Introduction

We all are well known by the importance of energy and its sources. Energy is the key factor in economic development of every country. The demand of energy is increasing day by day and the supplies of sources are limited. It is globally red alert for fossil fuel like Petrol, Kerosene, Natural Gas, LPG, and Lignite etc. This has made a huge gap between the demand and supply of energy. Renewable energy is the ultimate solution, which can fill this gap.
The briquette is an alternate source of energy. The biomass briquettes are substitute for coal and L.P.G., and research is going on. The Biomass briquettes are made up of renewable source of energy.
The briquetting piston-press is a reciprocating crank type mechanical press with flywheel. The main motor through continuous flat belt drives flywheel. The ground material is feed through a hopper by means of a screw conveyer with its own motor. The vertical screw pre compresses and forces the material downward in to the feeding chamber. From the chamber the materials forced by the ram through a tapered die system on to the cooling track in the form of briquettes. Briquettes formed are cylinder shape. [1]
In this study, we discussing about belt drive-open system of piston-press machine. Belts are used when the distance between the axes of the two shafts to be connected is considerable. A flat belt is a belt with a narrow rectangular cross-section. The flat belts are easier to use and are subjected to minimum bending stress.
In the present paper, the pulley is simulated with ANSYS 12.0.1 Software. This way the concern of different process parameters such as coefficient of friction, power, thickness of belt, slip and tension on belt are studied.

Discussion of various parts

(Figure 1) Briquetting plant consists from various parts. The main part is as follows:
Biomass-grinding machine: It is an important part of the briquetting plant, which function is to convert aggregate material in to small pieces.
Screw conveyor: it is used to carry the raw biomass from storage place to hopper. It is also used to mix the moisture socking agent from the raw biomass.
Piston-press machine:
a) Hopper: Hopper is use to move the raw material from screw conveyor to processing place. It includes extruder which is used to give a motion to raw biomass only in a one direction.
b) Ram: Ram is used for forcing the raw biomass in a die holder. Ram is fixed in ram holder. These ram moves in a horizontal direction with the help of motor.
c) Collar: Collar is use to fix the die in a die holder. Also it is used for to prevent the flow of raw biomass in a wrong direction i.e. in motor direction.
d) Die: Die is the part where the briquette get the shape to from the briquette.
Cooling tower: After process of briquette formation it cool at cooling tower and move in a direction of storage place. [2]
In piston-press machine all the rotary as well as reciprocating parts moving through the pulley belt arrangement. Therefore, pulley belt system is very important part of briquetting plant. In this study, discussing about pulley and bet system of briquetting plant (Figure 2).


Aim of Study

The main aim of this study is to investigate:
a) Effects of coefficient of friction (COF)
b) Effect of different Belt thickness (t) on the quality of belt
c) Effect of tension (T) on pulley
d) Effect of slip (s).


Methodology

(Figure 3)


Input Data

Diameter of Driver d1=0.15 m;
Diameter of Follower d2=0.85m;
Speed of Drier N1=1475rpm;
Speed of Follower N2=?;
Power P=20kW;

Estimation of tension during rotation of driving pulley

A highly elastic belt is used for belt drive, which is operated by 15 hp electric motor and at the speed of driver & driven pulleys are 1475rpm & 260rpm, the diameter of driver & follower pulleys are 150 mm & 850 mm. Center to Center distance is 1.575m (Table 1).
Finite element simulation of pulley: Figure 4 showing FE model of pulley model prepared in ANSYS 12.0.1.
The 3-D FE model for pulley was created by using ANSYS 12.0.1 software. The shaft is analyzed in ANSYS in three steps. First is preprocessing which involves modeling, geometric clean up, element property definition and meshing. Next comes, solution which involves imposing boundary conditions and applying loads on the model and then solution runs. Next in sequence comes post processing, which involves analyzing the results plotting different parameters like stress, strain, natural frequency, harmonic frequency and many. The mesh has been generated using tetra free element. The Solid 45 element type is adopted to mesh the model. The mesh of the pulley consists of 83198 elements. 17492 nodes are included in the finite element model. [3-5].


Result & Discussion

Present study deal with coefficient of friction between belt and pulley and variation of thickness of belt. The stress analysis have done through numerical simulation which shown in Figure 5-7.
Figure 5 showing when the coefficient of friction between the belt and pulley has increase then the value of tension (slack side & tight side) will decreases. But both line follow same pattern. And also the 0.2 to 0.3 coefficient of friction will better value between belt and pulley.
Figure 6 showing when the thickness of belt increases also with increase of pulley diameter than the slip of belt increases. But, when the thickness of belt increases also with decrease of pulley diameter than the slip of belt decreases.
Figure 7 showing pulley simulation of piston-press machine, this simulation shows the total deformation of pulley. In this figure value of maximum deformation is 0.193E-04.
Figure 8 showing that the von-Mises stress and shear stress on the pulley periphery through simulation.
Figure 9 showing simulation results. In this graph of belt tension has analysed in terms of power. When the belt tight side tension has increased than the value of stresses (von-Mises stress, principal stress, shear stress) have follow same pattern, but the stress will also increasing.


Conclusion

a) Coefficient of friction has play major role in tensions on belt.
b) Change of belt thickness decrease as well as increase the slip of belt. Also the change in diameter of pulley affects the slip of belt.
c) The simulation is easily finding the stress on pulley that occurs due to belt tension.

For More Open Access Journals Please Click on: Juniper Publishers
Fore More Articles Please Visit: Robotics & Automation Engineering Journal  

Comments

Post a Comment

Popular posts from this blog

Geometric Simulation for 3D-Printed Soft Robots- Juniper Publishers

Image
Juniper Publishers- Journal of Robotics Introduction Robots fabricated by soft materials can provide higher flexibility and thus better safety while interacting with natural objects with low stiffness such as food and human beings. With the growth of three-dimensional (3D) printing, it is even possible to directly fabricate soft robots [1,2] with complex structures and multiple materials realizing highly dexterous tasks like human-interactive grasping and confined area detection [3]. However, with such increased degrees of freedom (DoF), the design of soft robots becomes a very difficult task. It can be made possible by integrating simulation into the design phase. However, the shape deformation comes from many different and complex factors including manufacturing process, material properties, actuation, etc. Especially with the limited understanding of layer-based additive process in AM, it is challenging to formulate a complete mathematical model for the simul
Read more

Industry 4.0`S Product Development Process Aided by Robotic Process Automation- Juniper Publishers

Image
Juniper Publishers- Journal of Robotics Opinion As well defined on the journal`s site Robotic Process Automation (RPA) is the application of technology that allows employees in a company to configure computer software or a “robot” to capture and illustrate existing applications for processing a transaction, managing data, provoke responses and communicating with other digital systems. Product Development Process (PDA) is a key element for implementing Industry 4.0 and as defined in literature it consists of integrating six main elements: requirement, definition, design, production, maintenance and recycling [1-3]. So, in order to implement Industry 4.0 fast and costless we need to capture and illustrate existing applications as well as new ones for processing ensuring a reliable product-life cycle [4] and to efficiently process transactions, assuring smart services, manage big data and communicate with other digital systems. In other words Industry 4.0 is r
Read more

Research on Electromagnetic Driving Robot Fish-Juniper Publishers

Image
Juniper Publishers-Journal of Robotics Abstract Based on the actual physical appearance of the tuna and the wave equation derived from observing its swimming locomotion, this paper proposes a new idea on the simulation and modeling of the robot fish and a novel way of thinking on kinetic analysis. The motion law for each joint of the robot fish was first obtained through the discrete fitting method and the motion law was subsequently used as the basis for the robot fish electromagnetic drive control signal. The fluent flow field analysis software was utilized. The meshing of the fluid around the fish body was performed by using the dynamic grid technique. The surface pressure values of the fish body during the steady state forward movement were analyzed, and the values of the driving force of each part of the fish were obtained. It was then determined that the electromagnetic drive caudal fin robot fish was the optimal design. Based on the idea of digital-analog c
Read more